We have available, the Series 5610 NPort MOXA RS232 Device server, 60cm Rack mountable including mounting wings and power cable, in good serviceable condition, Cleaned and inspected for performance and operation, returned to factory default settings for easy setup. Accessible either using the front screen menu and toggle buttons or through the NPort Web Browser interface.
This unit has 16 potential RS232/485 or 422 inputs to Lan output. Serial whip to RJ45 and be supplied dependent upon configuration at an additional cost. these are an older revision of the current model but still fully functional and a fraction of the cost of a brand new unit.
With the NPort® 5600 Rackmount Series, you not only protect your current hardware investment, but also allow for future network expansion by centralizing the management of your serial devices and distributing management hosts over the network.
Only basic configuration is needed with the NPort® 5600 to connect up to 16 serial devices to an Ethernet network.
NPort® 5600 device servers come with Tx/Rx LEDs for the serial ports on the front panel, and 8 or 16 RJ45 serial port connectors on the rear panel. This makes the NPort® 5600 device servers suitable for a standard 19-inch rackmount, allowing you to simplify operational, maintenance, and administrative tasks.
Real COM/TTY drivers are provided to make the serial ports on the NPort® 5600 recognizable as Real COM ports by Windows, or Real TTY ports by Linux. In addition to supporting basic data transmission and reception, the NPort® drivers also support the RTS, CTS, DTR, DSR, and DCD control signals.
The System LED, serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The LEDs not only indicate current system and network status, but they also help field engineers monitor the status of attached serial devices.
When using termination resistors to prevent serial signal reflection, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible for all environments, the NPort® 5650-8/16 has DIP switches on the bottom panel for setting the termination and pull high/low resistor values.
Telnet Console, Web Console (HTTP/HTTPS), Windows Utility
ARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, RFC2217, Rtelnet, PPP, SLIP, SMTP, SNMPv1/v2c, TCP/IP, Telnet, UDP
Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2/2016/2019 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded
Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x
SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X, macOS 10.12, macOS 10.13, macOS 10.14, macOS 10.15
Android 3.1.x and later
HTTPS, AES-128, RSA-1024, SHA-1, SHA-256
HTTPS (TLS 1.2)
8 or 16 ports
NPort 5610 Series: RS-232
Disabled, Ethernet Modem, Pair Connection, Real COM, Reverse Telnet, RFC2217, TCP Client, TCP Server, UDP
Supports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 460.8k, 921.6k
5, 6, 7, 8
1, 1.5, 2
None, Even, Odd, Space, Mark
None, RTS/CTS (RS-232 only), DTR/DSR (RS-232 only), XON/XOFF
1 kilo-ohm, 150 kilo-ohms
ADDC® (automatic data direction control)
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Tx+, Tx-, Rx+, Rx-, GND
Tx+, Tx-, Rx+, Rx-, GND
Data+, Data-, GND
NPort 5610-8-48V/16-48V: 135 mA @ 48 VDC
NPort 5650-8-HV-T/16-HV-T: 152 mA @ 88 VDC
NPort 5610-8/16: 141 mA @ 100 VAC
HV Models: 88 to 300 VDC
AC Models: 100 to 240 VAC, 47 to 63 Hz
DC Models: ±48 VDC, 20 to 72 VDC, -20 to -72 VDC
19-inch rack mounting
480 x 45 x 198 mm (18.90 x 1.77 x 7.80 in)
440 x 45 x 198 mm (17.32 x 1.77 x 7.80 in)
NPort 5610-8: 2,290 g (5.05 lb)
NPort 5610-8-48V: 3,160 g (6.97 lb)
NPort 5610-16: 2,490 g (5.49 lb)
NPort 5610-16-48V: 3,260 g (7.19 lb)
3 in stock